Music and audio guides

Headphone data · AutoEq 10-band settings

EQ settings for 50 popular headphones

These are 10-band equalizer starting points for 50 widely used headphones, taken from the published AutoEq correction for each model and grouped by type. Each row gives a preamp and gains at 31 Hz to 16 kHz, so you can enter it in Echo or any 10-band graphic equalizer. We also summarize what the recommended corrections for 6,033 measured models say about how headphones usually deviate from a neutral target.

By HapibitsUpdated 9 min read

On this page

How to use these numbers

Set the preamp first, then enter the ten gains. Match the exact model and mode; an ANC, wired, or revised version can measure differently. Treat the 16 kHz value with caution: measurements that high depend heavily on fit, so cap it at about ±3 dB if it sounds harsh or dull. Listen at your usual volume and make small preference changes afterwards.

What the AutoEq data shows

We analyzed the recommended fixed-band correction for each of the 6,033 models in the AutoEq snapshot we mirror (8,853 published profiles). A positive gain means the headphone measures below the target in that band and needs a boost. A negative gain means it measures above the target and needs a cut.

Over-ear headphones (2,062 models) have a median correction of +4.4 dB at 31 Hz, and 44% need at least +3 dB of sub-bass. Open-back designs drive that result: 11 of the 14 wired over-ear models in our table need a 31 Hz boost.

Popular wireless headphones are tuned differently. 10 of the 11 wireless over-ear models in our table need a 31 Hz cut, because consumer tuning already adds bass above the neutral target.

Earbuds (111 models) are the bass-light group: 90% need +3 dB or more of sub-bass, because an open fit lets low frequencies escape. In-ear monitors (3,860 models) are more mixed: 17% need a bass boost and 15% need a cut.

Headroom matters for every type. 73% of over-ear corrections, 59% of in-ear corrections and 100% of earbud corrections need a preamp of −5 dB or lower. Skipping the preamp is the most common reason an EQ profile clips or distorts.

Median correction by headphone type

Median gain in dB for each band across all measured models of that type, using one recommended profile per model.

Median correction by headphone type
TypeModelsPreamp31621252505001k2k4k8k16k
Over-ear2,062−6.4+4.4+0.7−1.8−1.9+0.5−0.8+1.1+1.4+1.1−3.0
In-ear3,860−5.600−2.3−2.4+0.5+0.8−0.2+2.3+1.4−0.9
Earbud111−7.6+6.4+4.1+0.9−1.2−0.2−0.4−0.7+0.2+0.6+5.7

Wireless over-ear headphones: 10-band EQ settings

Gains in dB. Source is the measurement lab whose profile AutoEq recommends for that model.

Wireless over-ear headphones: 10-band EQ settings
HeadphonePreamp31621252505001k2k4k8k16kSource
Sony WH-1000XM6−4.6−4.9−2.1−3.2−1.4−1.0+3.4−1.5−0.7+5.3−9.8Kuulokenurkka
Sony WH-1000XM5−9.0−3.7−1.6−5.2−3.3+1.3+1.8+5.3−2.4+1.3+9.0oratory1990
Sony WH-1000XM4−5.8−4.3−1.8−5.8−1.4+0.5−0.6+6.0−0.8+1.0−2.2oratory1990
Apple AirPods Max−4.2−4.1−0.9−1.6−2.1−0.4−2.9+1.6+2.9+4.3−10.6oratory1990
Bose QuietComfort Ultra Headphones−5.2−3.5−2.7−1.1+1.6−1.8+1.1−1.0+1.1+0.1+5.2Rtings
Bose QuietComfort 45−1.9−1.4−1.2−2.1−0.9+0.7+2.0−0.9−1.3+1.0−10.0oratory1990
Bose QuietComfort 35 II−6.7+0.8−1.0−1.7−2.3−0.5+3.0+0.8−3.0+2.6+6.6crinacle
Sennheiser Momentum 4 Wireless−6.0−9.8−2.8−3.8−2.8+1.2−1.1+6.3−0.7+0.4+0.8oratory1990
Bowers & Wilkins Px7 S2−3.8−3.9−0.7−6.5−2.1+3.0+0.2+3.5+1.7−1.9+1.1oratory1990
Beats Studio Pro−4.2−4.7+3.0−1.4+4.1+1.6−0.4−3.0+0.8−3.8−0.1Rtings
Sony WH-CH720N−7.6−2.0+0.2−5.9−2.6+1.5+3.9+0.4+3.9−4.8+7.8Rtings

Wireless earbuds: 10-band EQ settings

Gains in dB. Source is the measurement lab whose profile AutoEq recommends for that model.

Wireless earbuds: 10-band EQ settings
HeadphonePreamp31621252505001k2k4k8k16kSource
Apple Airpods Pro 2−2.0−1.5+2.1+0.3−1.3−1.4−0.4+1.8+1.3+0.5−1.2HypetheSonics
Apple AirPods Pro−5.5+2.9+1.7+1.8+0.3−4.7−0.8−1.5+2.3+5.3+0.4crinacle
Apple AirPods 4−7.5+2.2−1.8−2.1−2.5−0.4−2.4−1.0+7.7+0.6−4.7Rtings
Apple AirPods (3rd generation)−11.9+7.8+0.5+0.5−0.70+0.8−3.7+1.9+1.1+12.0Rtings
Sony WF-1000XM5−4.8+2.0+0.1−2.2−1.9+1.0+1.2−1.5+1.5+0.9+4.8oratory1990
Sony WF-1000XM4−11.1−0.8−1.2−3.4−3.3−1.8−0.5+1.0+1.6+6.4+10.8oratory1990
Samsung Galaxy Buds3 Pro−2.7−2.1−0.7−0.6+0.5+2.9−1.3−2.7+2.9−0.8−6.4DHRME
Samsung Galaxy Buds2 Pro−1.9−2.4+0.5−0.3−0.70+0.2+0.6−1.9+2.6−7.9oratory1990
Samsung Galaxy Buds FE−1.5−1.5−1.2−0.3−1.3−0.4+1.5+0.4+1.5−1.2−4.6Regan Cipher
Google Pixel Buds Pro 2−3.0+2.6+1.6+0.9−0.8+1.7−1.5−0.9+0.9−1.4−0.5DHRME
Bose QuietComfort Ultra Earbuds−4.8−6.6−0.9+0.5+2.0+0.9+6.0−8.2+2.7−5.0+2.9DHRME
Nothing ear (2)−10.10−2.0−0.6+1.0−1.8+0.2−0.1+1.3+0.4+10.1Super Review
Beats Fit Pro−2.7−1.3−0.6+0.9+1.7+1.6−0.3−1.7−1.0−1.2+2.8Rtings
Anker Soundcore Liberty 4 NC−3.6+3.3−3.3−3.3−1.2+0.3+2.3+3.0+1.8−3.0−6.5Regan Cipher

Wired over-ear headphones: 10-band EQ settings

Gains in dB. Source is the measurement lab whose profile AutoEq recommends for that model.

Wired over-ear headphones: 10-band EQ settings
HeadphonePreamp31621252505001k2k4k8k16kSource
Sennheiser HD 600−7.5+6.9+3.3−1.1−1.6+0.6−0.8+0.1−1.0+3.9−6.5oratory1990
Sennheiser HD 650−7.4+7.0+2.6−1.2−2.2+0.5−1.0+0.7−1.2+5.1−3.6oratory1990
Sennheiser HD 560S−6.2+5.9+1.60−1.0+0.8−1.6+0.8−1.3+3.5−8.1oratory1990
Sennheiser HD 800 S−7.1+6.4+3.5−0.5−2.6−0.2−0.4+2.9−0.3−0.5−8.8oratory1990
Sennheiser HD 490 Pro−7.7+5.4+1.4−0.5−1.6+0.3−0.1+4.5−2.8−1.5+7.9Rtings
Beyerdynamic DT 770 Pro−2.5−4.1−1.4−1.8+2.6−0.4−0.5+0.1+3.2−4.1−10.2oratory1990
Beyerdynamic DT 990 Pro−6.1+6.0+0.6−1.8−1.3+3.4+1.0+0.9+0.3−5.4−12.0oratory1990
Audio-Technica ATH-M50x−2.30+0.4−5.3+0.7+1.9−1.0+0.6+0.4+2.8−9.3oratory1990
Audio-Technica ATH-M40x−3.2+3.7−1.6−4.3−0.3+2.8−0.5−0.1+3.3−0.6−12.0oratory1990
Sony MDR-7506−7.7+3.8−0.9−0.2+2.1+0.5+1.7+0.3−3.0−3.0+7.9oratory1990
AKG K371−4.8−3.0+1.2−1.4−1.8+0.8−0.8−0.3+3.0−0.2+4.8oratory1990
Philips SHP9500−7.5+6.9+3.5−1.5−0.6+1.2−1.5+4.1−2.6−1.3−4.3oratory1990
HIFIMAN Sundara−7.6+7.2+2.3+0.2−1.6−0.2−2.0+5.3−4.5+2.2−2.3crinacle
HIFIMAN Edition XS−5.1+4.8+1.7−0.6−1.7−0.50+3.1−1.5+0.8−12.0oratory1990

Wired in-ear monitors: 10-band EQ settings

Gains in dB. Source is the measurement lab whose profile AutoEq recommends for that model.

Wired in-ear monitors: 10-band EQ settings
HeadphonePreamp31621252505001k2k4k8k16kSource
Moondrop Aria−2.4−0.6+0.4−2.4−1.7+1.0+0.5−0.3+1.0+2.9−10.9oratory1990
Moondrop Chu 2−3.7−1.6+0.2−2.0−1.4+1.4+1.0−1.1−0.4+4.1−6.1HypetheSonics
Moondrop Blessing 2−3.9+3.4+2.7−0.2−1.6+1.0+0.6−2.2+2.0+1.9−9.4oratory1990
Truthear Hexa−2.0+0.1+1.7−0.4−1.9+0.6+0.4−0.6+2.1+0.5−8.5oratory1990
7Hz Salnotes Zero−2.7−0.4+1.7−0.6−1.0+0.4+0.3−1.2+0.2+2.8−2.4oratory1990
KZ ZSN Pro X−3.5+0.6+0.1−2.4−2.4+2.2+3.6−2.2+1.7−0.1−9.0oratory1990
Shure SE215−7.3+0.3−0.2−3.5−3.6+0.7+2.3−0.8+1.4+3.6+7.1oratory1990
Apple EarPods−10.7+6.4+4.8+1.0+1.4+2.0−0.8−6.7+3.0−0.7+10.7Super Review

Gaming headsets: 10-band EQ settings

Gains in dB. Source is the measurement lab whose profile AutoEq recommends for that model.

Gaming headsets: 10-band EQ settings
HeadphonePreamp31621252505001k2k4k8k16kSource
HyperX Cloud II−4.3+1.7−1.0−4.6−1.0+1.7+1.4−2.2+5.4−4.3−12.0oratory1990
SteelSeries Arctis Nova Pro Wireless−5.5−0.9+1.7−4.7+0.8+3.1−1.8−2.7+6.4−2.9+0.7Rtings
Razer BlackShark V2 Pro−6.2+1.4+0.8−6.8−3.5+6.7+1.7+1.7−1.6−0.8−1.8crinacle

Open any profile in the free EQ Finder

Every headphone above links to its exact profile in the free Headphone EQ Finder. There you can preview the curve, apply a bass or treble preference, and download the original AutoEq file or an Echo-ready export. The finder also covers the rest of the 6,033 models and variants.

Enter a profile in a 10-band equalizer

  1. Turn off other EQ

    Disable equalizers in your music app, earbuds companion app, and phone settings so corrections do not stack.

  2. Set the preamp

    Lower the preamp or output gain by the listed amount before adding any boosts.

  3. Enter the ten bands

    Match 31, 62, 125, 250, 500 Hz and 1, 2, 4, 8, 16 kHz. If your equalizer uses different centers, use the EQ Finder export instead of guessing.

  4. Check the top band

    If 16 kHz sounds piercing or dull, reduce that band toward 0 dB. Fit changes that region more than any other.

  5. Compare at the same loudness

    Toggle the profile on and off at matched volume. Louder almost always sounds better, which hides whether the correction helped.

Headphone EQ settings questions

Where do these EQ settings come from?
They are the fixed 10-band results published by the open-source AutoEq project for each model, from the recommended measurement source. The values come from a pinned snapshot (commit 7ae0f56) mirrored on 2026-10-10.
Why do some popular headphones need a bass cut?
Consumer wireless headphones are often tuned with extra bass. AutoEq corrects toward a neutral reference target, so it removes some of that emphasis. If you prefer the extra bass, keep the correction and add a small low shelf afterwards.
Why is the 16 kHz value so large for some models?
Very high frequencies are hard to measure consistently and change with fit, ear-tip seal and pad position. AutoEq still publishes a value, but a large 16 kHz boost or cut is the setting most worth reducing if it sounds wrong.
Will these settings sound perfect on my headphones?
They are a measured starting point, not a guarantee. Unit variation, fit, pads, ANC mode and personal preference all matter. Use the profile as a baseline and make small changes by ear.
My headphone is not in the table. What should I use?
Search the free Headphone EQ Finder, which covers 6,033 models and variants. Do not borrow a profile from a similar-sounding model name; the wrong profile can be worse than none.

Sources and methodology